钢筋加工棚性能强，造型美观，具备警示醒目的优点，那么该加工棚使用时有什么样的操作规范呢？

　　Rebar processing shed has strong safety performance, beautiful appearance and eye-catching warning advantages. Then what kind of operation specifications are there when the processing shed is used?

　　1、作业先前用手搬动飞轮，检查传动机构和工作装置，调整间隙，坚固螺丝，确认无误后启动空运转，检查轴承应无异响，齿轮应啮合良好。

　　1. Before operation, move the flywheel by hand, check the transmission mechanism and working device, adjust the clearance, firm the screws, and start the empty operation after confirmation. Check that the bearing should have the same sound and the gear should be in good engagement.

　　2、作业前检查润滑情况，按润滑表规定进行润滑；检查三角皮带松紧度；检查各传动机构有无异常现象，若系旋转刀盘剪断式，则先运转调直筒12分钟，运转正常后再起动切断机构，同时检查离合器是否灵活可靠。检查电路和开关，线头连接应牢固，保险丝应符合规定，电磁开关应接触可靠，动作灵活，接地应良好。

　　2. Check the lubrication condition before operation and lubricate according to the lubrication table; Check the tightness of triangle belt; Check whether the transmission mechanism has abnormal phenomenon. If it is a rotary cutter head shearing type, run the straightening cylinder for 12 minutes first, and start the cutting mechanism after normal operation. At the same time, check whether the clutch is flexible and reliable. Check the circuit and switch, wire connection should be firm, fuse should meet the requirements, electromagnetic switch should be reliable contact, flexible action, grounding should be good.

　　3、在调直块未固定，防护罩未盖好前不得穿入钢筋，以防机器开动后调直块甩出伤人。

　　3, in the straightening block is not fixed, the protective cover is not covered before the reinforcement, in order to prevent the straightening block after the machine starts to throw out wounding.

　　4、切去不直的料头或用锤头敲直料头，以利方便喂料；在导向筒前部安装一根一米长的钢管，先将要调直钢筋穿过钢管后，再穿入导向筒和调直筒，以防每盘钢筋接近调直完毕时甩出伤人。

　　4. Cut off the non-straight material head or knock the straight material head with a hammer to facilitate feeding; Install a one meter long steel pipe in the front of the guide cylinder. After the straightening steel bar passes through the steel pipe, it is put into the guide cylinder and the straightening cylinder to prevent each plate of steel bar from being thrown out when it is close to straightening.

　　5、必须在停机的条件下进行钢筋上盘、穿丝和引头切断或敲直。当钢筋穿入后，手与曳引辊必须保持一定距离，不得接近，以防造成伤手事故。

　　5, must be stopped under the condition of steel plate, wire threading and lead head cut or straight. When the steel bar penetrates, the hand and the drag roller must keep a certain distance, not close to prevent hand injury accidents.

　　6、机械运转中严禁打开各部防护罩及调整间隙，如发现有异常情况，应立即停机检查，不得强行使用。

　　6, mechanical operation is strictly prohibited to open each part of the shield and adjust the gap, if found abnormal situation, should immediately stop the inspection, not forced use.

　　7、作业中要检查各轴承温度，是检查调直筒轴承温度，各轴承温度不得高于60℃（以手摸能接受的热度为限）。

　　7. The temperature of each bearing should be checked in the operation, especially the temperature of aligning cylinder bearing. The temperature of each bearing should not be higher than 60℃ （limited to the heat that can be accepted by hand）。

　　8、停机后应松开调直筒的调直块回到原来位置，同时预压弹簧也必须回位。

　　8. After stopping the machine, the aligning block of the aligning cylinder should be loosened to return to its original position, and the preloaded spring must also return to its original position.

　　9、钢筋加工棚作业完后清理现场，机体上的污垢、灰尘，切断电源，锁好开关箱，并将调直切断的钢筋按规格分放整齐。

　　9. Clean up the site after the steel processing shed operation, remove the dirt and dust on the body, cut off the power supply, lock the switch box, and straighten the steel bar cut off according to the specifications.

　　如果您想了解更多内容的话，欢迎您随时通过网站pashaishaji.com联系我们进行咨询！

　　If you want to know more, you are welcome to contact us at any time through the website pashaishaji.com!