在施工现场，各种加工棚随处可见，它有很多种类，如配电箱加工棚、木工加工棚、钢筋加工棚等。这些加工棚的存在很好地预防了施工现场危险的发生，那么木工加工棚的搭建需要符合怎样的标准呢？

At the construction site, various processing sheds can be seen everywhere, including many kinds, such as distribution box processing shed, woodworking processing shed, reinforcement processing shed, etc. The existence of these processing sheds has well prevented the occurrence of hazards on the construction site. What standards should be met for the construction of woodworking processing sheds?

1、当临街通道、场内通道、出入建筑物通道、施工电梯及物料提升机地面进料口作业通道处于坠落半径内或处于起重机起重臂回转范围内时，要设置加工棚及防护通道，以避免发生物体打击事故。

1. When the street access, on-site access, building access, construction elevator and material elevator ground feed inlet operation channel are within the falling radius or within the slewing range of the crane boom, the processing shed and protective channel shall be set to avoid biological impact accidents.

2、通道、加工棚应采用建筑钢管扣件脚手架或其他型钢材料搭设，严禁采用竹木杆件搭设加工棚。

2. The passage and processing shed shall be erected with steel pipe fastener scaffold or other steel materials. It is strictly prohibited to erect processing shed with bamboo and wood rods.

3、通道及加工棚的顶部严密铺设双层正交竹串片脚手板或双层正交木模板的水平硬质防护，及封闭的防护栏或挡板，整体应能承受10kPa的均布静荷载。塔吊主要经行线路、转料平台、卸料平台落物曲线范围内的通道及加工棚顶部严密铺设双层正交厚木板。

3. The top of the passage and processing shed shall be closely paved with double-layer orthogonal bamboo string scaffold board or double-layer orthogonal wood formwork for horizontal hard protection, and the closed guard rail or baffle shall be able to withstand a uniform static load of 10kPa as a whole. The tower crane mainly passes through the route, the transfer platform, the passage within the falling curve range of the unloading platform, and the top of the processing shed, which is closely paved with double-layer orthogonal thick plank.

4、特别重要或大型的通道、加工棚及悬挑式防护设施要制定专项技术方案，经企业技术负责人审批后实施。

4. Special technical schemes shall be formulated for particularly important or large passages, processing sheds and cantilevered protective facilities, which shall be implemented after being approved by the technical director of the enterprise.

5、通道的搭设：通道净空高度和宽度应根据通道所处位置及人、车通行要求确定，高度一般不低于3.5米，宽度一般不低于3米。高度在15m米以下建筑物，其进出口通道长度不低于3米。高度在15-30米的建筑物，其进出口通道长度不低于4米。高度超过30米的建筑物，其进出口通道长度不低于5米。通道长度自脚手架外排立杆起算。

5. Passage erection: The clearance height and width of the passage shall be determined according to the passage location and the requirements for people and vehicles. The height is generally not less than 3.5 meters, and the width is generally not less than 3 meters. For buildings with a height below 15m, the length of the entrance and exit passage shall not be less than 3m. For buildings with a height of 15-30 meters, the length of the entrance and exit passage shall not be less than 4 meters. For buildings with a height of more than 30 meters, the length of the entrance and exit channels shall not be less than 5 meters. The length of the passage shall be calculated from the vertical poles outside the scaffold.

以上就是搭建加工棚的标准了，只有正确搭建，才能发挥出加工棚的作用，预防施工时各种危险情况的发生。关注我们http://pashaishaji.com，带您了解相关的更多注意事项！

The above is the standard for setting up the processing shed. Only by setting up the processing shed correctly can it play its role and prevent various dangerous situations during construction. Follow us http://pashaishaji.com , let you know more about the relevant precautions!